Wine cabinet Meyvel MV12-SF2 (easy)

IMPORTANT: Before installation and use, read all instructions and make sure that the voltage (V) and frequency (Hz) indicated on the nameplate exactly match the voltage and frequency in your home. The nameplate is located on the front left side of the outside of the wine cabinet.

The manufacturer declines all responsibility in the event that the installer does not comply with all applicable safety regulations that are necessary for the normal use and normal operation of the electrical system.

Two or more people are required to install the instrument to avoid injury or damage to the instrument.

When moving the Wine Cooler, do not tilt it more than 45 °.

Remove all contents of the wine cabinet before moving.

Location selection.

• The wine cabinet should not be in direct sunlight, constantly exposed to heat or extreme temperatures (for example, near a radiator or boiler). If this is not possible, install an insulating plate between the appliance and an adjacent heat source.
• Check to see if there is an electrical outlet available after your appliance is installed.
• Anything above the appliance must be at least 10 cm apart to ensure sufficient cooling of the condenser, and a 5 cm gap must be left behind and on both sides of the appliance.
• Be sure to leave enough room to open the door to avoid damage to the appliance or injury.

Height adjustment and leveling of the wine cabinet.

• The appliance is equipped with adjustable feet, so the height can be adjusted to level the cabinet on uneven floors.
• We recommend that two people perform this procedure.
• Make sure the cabinet is maintained at all times.
• Rotate the leg to a suitable position to level the cabinet.
• Repeat these steps for the other adjustable feet.
• Use a spirit level to level the wine cabinet so that it operates normally and quietly..

IMPORTANT: If the appliance is installed unevenly, it could damage the door and the door seal.

IMPORTANT: Do not move the appliance with the feet set high.

Connection.

• Check the frequency of the power supply and the voltage supplied to the wine cabinet. Make sure the plug on the power cord matches the outlet.
• Plug in the power cord to check if the power is on and the wine cabinet is working normally.
• When using the Wine Cooler for the first time (or if the Wine Cooler has been turned off for a long time), during the first two hours of operation, set the required temperature and humidity and do not place your wines inside the cabinet. Place them in there after the first two hours of wine cabinet operation.

Power Supply::

Press the ON/OFF button to turn on the cabinet. Tap it again to turn it off.

Led indicator:

Press the touch button to turn on the LED cabinet light, press it again to turn off the light.

Temperature range:

Press the temperature button to toggle the temperature display in Celsius or Fahrenheit.

Anti-fogging:

When condensation appears on the outer glass door, press the De-fogging button. Press the De-fogging button again to turn it off after the condensation has disappeared.

Temperature setting

• In standby mode, press the Setup button and the temperature display will flash.
• Press the "Up" or "Down" control buttons to set the desired temperature, then release the button.
• Press the SET button again to save the temperature setting, or it will be saved automatically after 5 seconds.
• After saving the temperature setting, the actual temperature inside the cabinet will be displayed and the temperature setting will be set accordingly.
• Temperature range: 5-22 degrees Celsius.

Setting humidity parameters

• In standby mode, press the setting button twice, at this time, the humidity display will flash.
• Press the control buttons "Up" or "Down" to set the desired humidity, then release the button.
• Press the "Setup" button again to save the humidity value, or it will be saved automatically after 5 seconds.
• After saving the humidity parameter, the humidity display will show the actual humidity inside the cabinet and the humidity will be adjusted accordingly.
• Humidity range: 56% -78%

Cooling system:

If the temperature in the cabinet exceeds the set temperature by 2 degrees Celsius, the compressor will start and the cooling indicator will turn on.

When the set temperature inside the cabinet is reached, the compressor will stop and the cooling indicator will turn off.

Heating system:

If the temperature in the cabinet is 2 degrees Celsius below the set temperature, heating will start and the heating indicator will turn on. When the internal temperature reaches the set value, heating will stop and the heating indicator will turn off.

Humidification system:

If the humidity in the cabinet is 2% below the set value, the humidification system will start and the humidification indicator will turn on. When the indoor humidity reaches the set value, humidification will stop and the humidification indicator will turn off.

Excess moisture elimination system:

If the humidity in the wine cabinet is 2% higher than the set value, the humidity starts to decrease. When the internal humidity drops to the set value, the removal of excess humidity will stop.

Attention:

• The temperature and humidity are set at the factory, the wine cabinet is ready for use with the set values.
• If the consumer finds an incorrect humidity value, he should contact the service center.

Humidity test:

• Fill the water tank with distilled water.
• Setting the temperature required for wines (or cigars), recommended temperature: 16 degrees Celsius and humidity: 66%.
• It is possible to place a 3rd humidity sensor in the middle of the cabinet.
• After the wine / cigar cabinet has been in operation for 24 hours, compare the difference between the placed thermometer and hygrometer and the values on the control panel.